|
Sensing Beam
|
Visible red, class 2 laser, 650 nm
|
|
Supply Voltage
|
12 to 30 V dc
|
|
Power & Current Consumption (exclusive of load)
|
Normal Run Mode:1.7 W, Current consumption < 70 mA at 24 V dc
|
|
Sensing Range
|
100 mm to 1000 mm (3.94 in to 39.37 in)
|
|
Output Configuration
|
Analog output: 4 to 20 mA or 0 to 10 V, depending on model
Discrete output:Discrete NPN/PNP is userconfigurable
|
|
Output Ratings
|
Discrete output ratings: 100 mA maximum (protected against continuous overload and short circuit)
OFF-state leakage current—PNP:< 10 μA at 30 V
OFF-state leakage current—NPN:< 200 μA at 30 V
Output saturation voltage—PNP outputs:< 3 V at 100 mA
Output saturation voltage—NPN outputs:< 1.6 V at 100 mA
Analog current output (LE...I Models):1 kΩ max. @ 24 V; max. load resistance = [Vcc-4.5/0.02 Ω]
Analog voltage output (LE...U Models):2.5 kΩ min. load resistance
|
Remote Input
|
Allowable Input Voltage Range: 0 to Vcc
Active Low (internal weak pullup—sinking current):
High State > 4.3 V at 740 μA max.
Low State < 1.3 V at 800 μA max.
Active High (internal weak pulldown—sourcing current):
High State > 4.3 V at 1.7 mA max.
Low State < 1.3 V at 1.6 mA max.
|
|
Supply Protection Circuitry
|
Protected against reverse polarity and transient overvoltages
|
|
Analog Resolution
|
100 mm to 600 mm: < 0.5 mm
600 mm to 1000 mm: < 1 mm
|
|
Analog Linearity
|
Linearity is the lesser of Accuracy or 0.5% of full scale range (± 4.5 mm) at any given distance.
|
|
Measurement / Output Rate
|
< 1 ms
|
|
Response Time
|
Fast: 2 ms
Standard:5 ms
Medium:15 ms
Slow:50 ms
|
|
Delay at Power Up
|
< 1 s
|
|
Ambient Light Immunity
|
> 10,000 lux
|
|
Minimum Window Size, Analog and Discrete
|
10 mm (0.39 in)
|
|
Bore Spec
|
1 cm radius at 1 m
|
|
Maximum Torque
|
2 N·m (17.7 in-lbs)
|
|
Indicators
|
Power LED Indicator:
Solid Green = Normal operation, power On and laser On
Flashing Green (1 Hz) = Power On and laser Off (laser enable mode)
Analog Output LED Indicator:
Solid Amber = Target is within the taught window
Off = Target is outside the taught window
Discrete Output LED Indicator:
Solid Amber = Discrete Output is On
Off = Discrete Output is Off
|
|
Construction
|
Housing: die-cast zinc
Lens cover:polycarbonate
|
|
Vibration / Mechanical Shock
|
All models meet Mil. Std. 202 G requirements method 201A. Also meets IEC 60947-5-2.
|
|
Environmental Rating
|
IP67, NEMA 6
|
|
Operating Conditions
|
Temperature: −20 °C to +55 °C (−4 °F to +131°F)
Humidity: 90% at +55 °C (non-condensing)
|
|
Storage Temperature
|
−30 °C to +65 °C (−22 °F to +149 °F)
|
|
Application Note
|
For optimum performance, allow 10 minutes for the sensor to warm up.
|